How to Install Indoor LED Wall

Feb 8, 2022 | Installation, knowledgebase | 32 comments

How to install indoor led wall

1. Preparations

1.1. Unpacking

Warning: To prevent damage to the LED panel, wear anti-static gloves before installing/touching the display. After unpacking, do not place the display vertically on the floor, an accident such as a fall may be caused.

Table of Contents
;
3

Die-casting LED Display Cabinets Installation

Use a pair of scissors to cut the sealing tape on the cardboard box. Carefully take the cabinet and accessories out of the cardboard box. After opening the cardboard box, ensure that the contents are complete and in good condition.
package of indoor led display
• LED Cabinets &LED Modules

• Power cable;LAN cable (RJ45, CAT-5)

• Connection plates

• LED Controller

led display and accessories visionpi led display
1.3. Tools

• LED Cabinets &LED Modules

• Power cable;LAN cable (RJ45, CAT-5)

• Connection plates

• LED Controller

led screen installation tools
• Test led modules

Press the CHECK button on the back of each cabinet to check if the product can operate normally.

test led display

2. Structure Installation

Precautions when handling the cabinets:

• Do not drop or apply shock/vibration to the product. Strong impacts may damage the component inside.

• Only a qualified service technician should perform the installation.

• Only use approved cabinets. • Be careful not to damage the corners of the cabinet.

• Install the display in a well-ventilated area.

• Always wear anti-static gloves when touching the display.

• Provide air conditioning around the LED display to allow heat dissipation away from the display.

• To maintain proper ventilation, keep clear space from the mounted displays to the wall. Installing the product in poorly ventilated spaces may damage the LED.

led display installation standing structure

Wall Mount Kits

A wall mount kit is made of aluminum profile 40x40mm (in some regions sold separately or available from third party vendors) allows you to mount the LED display on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. Wall mounting can only be performed from the front side of cabinets.

wall mounted structure led wall visionpi
1. Fixed the aluminum profile on the wall with anchors. Insert cage nuts into the slot of the aluminum pipe

2. Insert the connection plate on the structure, and use the Allen screw bolt to connect the cage nuts.

led wall wall mouted structure
3 connect cabinets with structure by connection plate with Allen; connect cabinets together by faster lockers

4. Install led modules (follow the arrow direction of the modules)

led screen installation steps

3. Cabinet installation

Step 1. Use a gradienter to adjust the flatness and verticality and then secure the cabinet to the connectors on the rack frames. Use connection plates to fix the screen. Start your installation from the bottom row. Install the connecting plates on the bracket (Fig 1). Rotate the hex key clockwise until the screw bolts are inserted, and fasten the fast locker on between two cabinets (left to right, up to down)(Fig2.) ※Do not fix the screws between the connectors and cabinets too tight for future adjustment.

led screen cabinet installaiton
Step 2. Install the connecting plates on the structure. Rotate the hex key clockwise until the screw bolts are inserted. Do not over-tighten the screw bolts yet as you may need to adjust the connecting plates again. Ensure that the seam and flatness between cabinets conform to the standard after each cabinet is installed. Otherwise, make some adjustments, lockout LED lamp boards after they are adjusted horizontally and vertically because the boards will probably be moved during the installation of other lamp boards. Repeat the above steps to install the other cabinets in the lowest row.
connect two led screen cabinet
Step 3. fasten the lockers and check the unevenness of the nearby cabinets, and adjust them by the hex, loosen, or tighten to bring the cabinets to the same level. can use fingers to feel the “cross” of four nearby cabinets to see if the cabinet is well aligned. Ensure that all the cabinets are flat and vertical and the seams between the cabinets are even. Then tighten the screws to complete the installation.
cabinets connection

4. Power and Signal Wiring

The data wiring process must follow a zigzag order between the cabinets, always starting from the one located at the bottom left. The modules are then connected to the data in and data out ports. Thanks to our system software we can verify the correct wiring of the entire screen with simple tests. Finally follows the color calibration and brightness setting.

 5. LED Modules installation.

After check all the cabinets are well installed, attach the led modules to the cabinet, please check the arrow on the back of the PCB and follow the direction, and connect the flat cable and power cable from the hub to each of the modules. tips: to check the status of each led module on the cabinet, you can use one spare cabinet to test the condition of the led modules by pressing the test button on the hub.

led modules installaiton step 4
To install the module to the hub board, the flat cable that connects between them has to be properly wired. One end of the flat cable is already attached to the hub board, use the other end to connect it to the module. Before connection, make sure that the arrow sign on the module ispointing up. Connect the flat cable to the connector on the module until it clicks into place. 
modules installaiton indoor led screen

Modular Cabinet 320x480mm Installation

320x480mm led cabinet installation layout
320x480mm led cabinet installation layout

Subscribe To Our Newsletter

Join our mailing list to receive the latest news and updates from our team.

You have Successfully Subscribed!

Pin It on Pinterest